在日常的学习、工作、生活中,肯定对各类范文都很熟悉吧。范文怎么写才能发挥它最大的作用呢?下面是小编帮大家整理的优质范文,仅供参考,大家一起来看看吧。
思科小型企业网络设计篇一
widesign(300-360)考试检验考生是否具备识别客户和应用需求,实施预测无线设计原则和执行站点调查所需的企业无线网络设计和优化的.能力。下面是考试的主要内容:
1.1 identify business and rf application needs
1.2 identify client density, capabilities and their impact on the wireless network
1.2.a client quantity, radio type, spatial streams
1.3 identify the challenges of setting up a wireless network by various vertical markets
1.4 describe required site survey documentation
1.4.a customer questionnaire
1.4.b floor plans & their quality
1.4.c describe the deliverables of the site survey
1.5 identify coverage area requirements
1.5.a mesh
1.5.b high density
1.5.c security sensitive
1.5.d real time applications
2.1 describe impact of regulatory domains
2.1.a mesh
2.1.b channel and power
2.1.c multi-national deployments
2.2 identify deployment location safety considerations
2.3 identify the impact of customer aesthetic limitations on the installation
2.4 assess the existing wired and wireless infrastructure
2.4.a determine high-throughput and very high throughput (vht) protocol (n/ac) impact
2.4.b determine existing wireless infrastructure if required
2.5 identify impact of material attenuation
2.5.a walls, cubicles, and the likes
2.5.b single/multi-floor
2.5.c campus
2.5.d warehouse/retail
2.5.e subtitle number 2.2
3.1 select the criteria used for coverage design
3.1.a data vs voice vs video vs location
3.2 demonstrate the impact of frequency planning in a high density environment
3.2.a band select for high density
3.2.b optimize 2.4 ghz radio utilization
3.2.c legacy devices
3.2.d channel width
3.3 use pi and ekahau planning tools to make network plan
3.3.a enter network requirements in the tool
3.3.a.[i] capacity requirements
3.3.a.[ii] coverage requirements
3.3.b define the environment
3.3.b.[i] maps and scale
3.3.b.[ii] types of rf obstacles
3.3.c place and configure simulated aps and antennas
3.3.c.[i] place simulated aps (manual, automatics)
3.3.c.[ii] adjust aps and antennas / ap tx power height and down tilt
3.3.d analyze key network metrics using heat maps for 2.4 and 5ghz
3.3.d.[i] analyze coverage, snr, and channel overlap
3.3.d.[ii] analyze ap placements in regards to real time handoffs around corner
4.1 identify the appropriate site survey equipment and access requirements based on environmental needs
4.2 complete the layer 2 site survey for indoor, and outdoor mesh environments
4.2.a select proper ap and antenna for conducting site survey
4.2.b configure ap
4.2.c survey for worst case client
4.3 complete layer 1 survey (cisco cleanair, metageek chanalyzer)
5.1 verify rf coverage
5.1.a utilize tools (ekahau) for audit
5.1.b rrm, controller
5.1.c analyze snr, channel overlap, and packet loss
5.2 verify network applications and performance
5.2.a apply pi tools (voice readiness, location readiness, site calibration)
5.3 reconcile any deployment issues
5.4 assemble and deliver installation report to customer
5.4.a indoor
5.4.b outdoor mesh
6.1 determine physical infrastructure requirements
6.1.a ac power and poe
6.1.b understand cable plant considerations
6.1.c mounting considerations: nema
6.1.d outdoor grounding and lighting protection
6.1.e rack capacity
6.1.f switch port capacity
6.2 determine logical infrastructure requirements
6.2.a determine ap count, controller count, and license requirements
6.2.b decide the type of architecture for the deployment
6.3 describe ipv6 optimization on the wlc
6.3.a ra filter
6.3.b dhcp server guard
6.3.c dhcpv6 source guard
7.1 describe the relationship between real time applications & the wireless networks
7.1.a packet error rate (per)
7.1.b rf coverage
7.1.c bit error rate (ber)
7.1.d qos
7.1.e call admission control (cac)
7.1.f client roaming decision algorithm
7.2 describe voice and video as they apply to the wireless network
7.2.a device capabilities (hardware and software)
7.2.b call setup/data flow overview
7.2.c other wireless voice and video services (i.e. jabber, lync, skype, viber, facetime)
7.2.d standards and wifi alliance (wfa) certifications (.11r, .11e, .11n/ac, .11k, cckm, voice enterprise, voice personal, wmm, uapsd)
7.2.e cisco compatible extensions (voice features)
7.2.f voice and video codecs
7.2.g skinny client control protocol (sccp)
7.2.h session initiation protocol (sip)
7.3 describe real time applications (other than voice and video) as they apply to the wireless network
7.3.a session based and non-session based
7.3.b roaming sensitivity
7.3.c disconnection issue
7.4 design wireless roaming parameters for supporting real time applications
7.4.a 802.11 r/k, cckm, okc, mobility groups, interface groups,
7.4.b tuning rf parameters
7.4.c ap placement considerations
7.5 design wireless parameters for supporting real time applications
7.5.a minimum speed requirements-rssi and snr
7.5.b client transmit and receive sensitivity / mismatch with ap
7.5.c cell overlap requirements
7.5.d cell separations
7.5.e traffic control and management, qos, vlan, wmm, avc
7.5.f delay and jitter requirements
7.5.g cac and tspec
7.5.h spectrum
7.5.i 802.11n/ac enhancements
7.5.j concurrent client connections
7.5.k band select
s("content_relate");【2017设计思科无线企业网络考试主要内容】相关文章:
1.设计思科无线企业网络考试主要内容2.2017部署思科无线企业网络考试要点3.部署思科无线企业网络考试要点4.保护思科无线企业网络考试要点5.保护思科无线企业网络考试要点(最新)6.故障排除思科无线企业网络考试概述和要点7. arch思科网络服务架构设计考试主要内容8.故障排除思科无线企业网络考试大纲

一键复制